Avatar
Search
Forum Scope




Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_PrintTopic sp_TopicIcon
Unburned powder ?
sp_NewTopic Add Topic
Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
1
March 5, 2024 - 12:57 pm
sp_Permalink sp_Print sp_QuotePost

I shot some reloads yesterday and noticed some unburned powder remained in the bore .

The loads were 38 55 and I used 27.5 grains of 3031 with some factory primers and some CCI bench rest primers , should I try a different powder ?

Avatar
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 5735
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
2
March 5, 2024 - 1:35 pm
sp_Permalink sp_Print sp_QuotePost

Any idea how old the powder may be? How has it been stored? Bullet weight? Barrel length? Load sounds good.

 

Mike

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
3
March 5, 2024 - 1:44 pm
sp_Permalink sp_Print sp_QuotePost

TXGunNut said
Any idea how old the powder may be? How has it been stored? Bullet weight? Barrel length? Load sounds good.

 

Mike

  

Hey Mike , the powder is less than a year old , kept in my work room upstairs in the container it came in , lid closed tight , bullet weight is 260 grain cast from bear creek and barrel lengths are 22″ and 26″ , both old model 1894’s .

Avatar
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 5735
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
4
March 5, 2024 - 2:00 pm
sp_Permalink sp_Print sp_EditHistory sp_QuotePost

Chris-

How’s the accuracy? If not what you’re expecting you could move up or down a half grain at a time. I’ve had good results with a bit heavier charge of 3031, Lyman lists 26 grains as a potentially accurate load with what may be a similar bullet. A chronograph may be helpful in identifying a consistent load. 

 

Mike

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
5
March 5, 2024 - 2:11 pm
sp_Permalink sp_Print sp_QuotePost

TXGunNut said
Chris-

How’s the accuracy? If not what you’re expecting you could move up or down a half grain at a time. I’ve had good results with a bit heavier charge of 3031, Lyman lists 26 grains as a potentially accurate load with what may be a similar bullet. A chronograph may be helpful in identifying a consistent load. 

 

 

M8ke

  

Accuracy is pretty good out of the 22″ barreled 1918 made and high out of the 26″ barreled 1902 made  .I did try a few with 28 grains with the same results.

Avatar
NY
Member
Restricted
Forum Posts: 7119
Member Since:
November 1, 2013
sp_UserOfflineSmall Offline
6
March 5, 2024 - 2:19 pm
sp_Permalink sp_Print sp_QuotePost

Unburned powder means insufficient pressure.  Heavy crimp would increase pressure, but could be detrimental to accuracy.  If you can find magnum primers, that’s worth trying, too.

Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
7
March 5, 2024 - 2:23 pm
sp_Permalink sp_Print sp_QuotePost

clarence said
Unburned powder means insufficient pressure.  Heavy crimp would increase pressure, but could be detrimental to accuracy.  If you can find magnum primers, that’s worth trying, too.

  

Okay I’ll give that a try , thanks .

Avatar
Kingston, WA
Admin
Forum Posts: 11834
Member Since:
April 15, 2005
sp_UserOfflineSmall Offline
8
March 5, 2024 - 6:08 pm
sp_Permalink sp_Print sp_QuotePost

My pet load for the 38-55 is 23.5 grains of IMR 4198… it is a very mild load, but it is wonderfully accurate in my Single Shot (high-wall) rifle.  Hodgen lists 24 grains of H4198 as a starting load with 28 grains as max.  In your shoes, I would start with the 24-grain load and see how it performs in your rifles.

Bert

WACA Historian & Board of Director Member #6571L
High-walls-1-002-C-reduced2.jpg

Avatar
Member
WACA Member
Forum Posts: 1996
Member Since:
September 22, 2011
sp_UserOfflineSmall Offline
9
March 5, 2024 - 7:48 pm
sp_Permalink sp_Print sp_QuotePost

Bert H. said
My pet load for the 38-55 is 23.5 grains of IMR 4198… it is a very mild load, but it is wonderfully accurate in my Single Shot (high-wall) rifle.  Hodgen lists 24 grains of H4198 as a starting load with 28 grains as max.  In your shoes, I would start with the 24-grain load and see how it performs in your rifles.

Bert

What is the weight and bullet mould of your presumably cast bullet used?

Avatar
Kingston, WA
Admin
Forum Posts: 11834
Member Since:
April 15, 2005
sp_UserOfflineSmall Offline
10
March 5, 2024 - 9:08 pm
sp_Permalink sp_Print sp_QuotePost

mrcvs said

Bert H. said

My pet load for the 38-55 is 23.5 grains of IMR 4198… it is a very mild load, but it is wonderfully accurate in my Single Shot (high-wall) rifle.  Hodgen lists 24 grains of H4198 as a starting load with 28 grains as max.  In your shoes, I would start with the 24-grain load and see how it performs in your rifles.

Bert

What is the weight and bullet mould of your presumably cast bullet used?

  

255-grain bullet weight.  I bought the laser-cast bullets from Oregon Trail – TrueShot / Cast Bullet (oregontrailbullets.com)

WACA Historian & Board of Director Member #6571L
High-walls-1-002-C-reduced2.jpg

Avatar
Member
WACA Member
Forum Posts: 1996
Member Since:
September 22, 2011
sp_UserOfflineSmall Offline
11
March 5, 2024 - 10:01 pm
sp_Permalink sp_Print sp_QuotePost

Thank you, Bert!

Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
12
March 6, 2024 - 4:16 am
sp_Permalink sp_Print sp_QuotePost

Bert H. said
My pet load for the 38-55 is 23.5 grains of IMR 4198… it is a very mild load, but it is wonderfully accurate in my Single Shot (high-wall) rifle.  Hodgen lists 24 grains of H4198 as a starting load with 28 grains as max.  In your shoes, I would start with the 24-grain load and see how it performs in your rifles.

Bert

  

Thanks Bert , I’ll give that a try .

Avatar
Member
WACA Member
Forum Posts: 44
Member Since:
September 3, 2018
sp_UserOfflineSmall Offline
13
March 6, 2024 - 9:47 am
sp_Permalink sp_Print sp_QuotePost

What diameter of cast bullet are you using? Most of those old 38-55 barrels are .379-.381 bores. Anything less bullet diameter can cause what you are seeing. Matching bullet to the bore is everything with those guns. Try 10 grains of Unique powder. That fast powder will often “bump” up a cast bullet to the bore diameter. If that works it is a good indication your cast bullet diameter is a little small.

Avatar
South Texas
Member
WACA Member
Forum Posts: 1064
Member Since:
March 20, 2010
sp_UserOfflineSmall Offline
14
March 6, 2024 - 7:03 pm
sp_Permalink sp_Print sp_QuotePost

I run my 255grn cast bullets (20:1 Lead, 255 grn bullet with gas check, 0.280″ diameter) with 28.5 grns of IMR 3031 (average 1587 fps).  For similar performance, and load I prefer,  uses 22 grn of Accurate 5744 (average 1615 fps). 

DSC_0245-Copy-3.JPG

1892takedown @sbcglobal.net ......NRA Endowment Life Member.....WACA Member

"God is great.....beer is good.....and people are crazy"... Billy Currington

Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
15
March 7, 2024 - 1:16 pm
sp_Permalink sp_Print sp_QuotePost

[email protected] said
What diameter of cast bullet are you using? Most of those old 38-55 barrels are .379-.381 bores. Anything less bullet diameter can cause what you are seeing. Matching bullet to the bore is everything with those guns. Try 10 grains of Unique powder. That fast powder will often “bump” up a cast bullet to the bore diameter. If that works it is a good indication your cast bullet diameter is a little small.

  

I’m using .380 cast bullets , both rifles slugged at .379 , I was also told to try blue dot powder . I have neither blue dot or unique , maybe I will get some and try that , thanks !

Avatar
Rural Nevada
Member
WACA Member
Forum Posts: 131
Member Since:
December 12, 2019
sp_UserOfflineSmall Offline
16
March 7, 2024 - 3:22 pm
sp_Permalink sp_Print sp_QuotePost

Just what does your unburned 3031 look like?  Are you seeing entire particles (full sticks) remaining in the barrel after firing?  Are they distributed down the length of the barrel or just a few in the throat?  Or is it more of partially burned sticks remaining in the barrel?

 

If I encountered partially burned powder in a handload, all of these things would be useful in determining the underlying cause.

 

I’m interested in seeing what you find as the ultimate cause of this.

Paul

Nevada Paul

Life Member NRA

Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
17
March 7, 2024 - 4:36 pm
sp_Permalink sp_Print sp_QuotePost

Nevada Paul said
Just what does your unburned 3031 look like?  Are you seeing entire particles (full sticks) remaining in the barrel after firing?  Are they distributed down the length of the barrel or just a few in the throat?  Or is it more of partially burned sticks remaining in the barrel?

 

If I encountered partially burned powder in a handload, all of these things would be useful in determining the underlying cause.

 

I’m interested in seeing what you find as the ultimate cause of this.

Paul

  

I noticed a couple full sticks close to the chamber , maybe four inches or so from there .

Chris

Avatar
Rural Nevada
Member
WACA Member
Forum Posts: 131
Member Since:
December 12, 2019
sp_UserOfflineSmall Offline
18
March 7, 2024 - 6:31 pm
sp_Permalink sp_Print sp_QuotePost

If no more unburned powder than ‘a couple of sticks’, and this has never happened previously with this lot of powder and firearm, I’d suspect a primer (old, too mild, faulty) before doing anything more radical.

It’s probably not possible now, after the fact, but it would be useful to know if every shot contributed to the residual unburned powder, or did a single load perhaps create the entire problem.

You’ve had plenty of useful suggestions here from experienced reloaders. If you do, in fact, discover what caused the issue, I’m sure many of us would like to hear.

Nevada Paul

Life Member NRA

Avatar
Member
WACA Member
Forum Posts: 84
Member Since:
October 8, 2023
sp_UserOfflineSmall Offline
19
March 8, 2024 - 12:43 pm
sp_Permalink sp_Print sp_QuotePost

Nevada Paul said
If no more unburned powder than ‘a couple of sticks’, and this has never happened previously with this lot of powder and firearm, I’d suspect a primer (old, too mild, faulty) before doing anything more radical.

It’s probably not possible now, after the fact, but it would be useful to know if every shot contributed to the residual unburned powder, or did a single load perhaps create the entire problem.

You’ve had plenty of useful suggestions here from experienced reloaders. If you do, in fact, discover what caused the issue, I’m sure many of us would like to hear.

  

Thanks Paul , I’ll let you all  know if I figure it out  .

Forum Timezone: UTC 0
Most Users Ever Online: 4623
Currently Online: wally, twobit, Mark Douglas, rogertherelic, Anthony, Big Larry, joe45c
Guest(s) 101
Currently Browsing this Page:
1 Guest(s)
Top Posters:
clarence: 7119
TXGunNut: 5735
Chuck: 5123
steve004: 4762
1873man: 4511
Big Larry: 2467
twobit: 2383
mrcvs: 1996
TR: 1805
Forum Stats:
Groups: 1
Forums: 18
Topics: 13714
Posts: 121094

 

Member Stats:
Guest Posters: 1934
Members: 9414
Moderators: 4
Admins: 3
Navigation