Log In
March 25, 2024
Offline
ANTHONY I would like to try to find a member that has a 66 with genuine factory CF bolt that would be willing to have all the dimensions taken by a trained machinist for accurate measurements let me know if you think this is a something that I should pursue or not my best as always to you and yours gene 66
December 9, 2002
Offline
gene66 said
ANTHONY I would like to try to find a member that has a 66 with genuine factory CF bolt that would be willing to have all the dimensions taken by a trained machinist for accurate measurements let me know if you think this is a something that I should pursue or not my best as always to you and yours gene 66
gene,
I am very aware of you’re pursuit in this as we’ve discussed in the past and can understand you’re posting this here on the general forum. You’ve been searching for a spare or extra M-1866 bolt with the Center Fire conversion intact that has proven over the years to be as rare as the old proverbial “Hens Teeth”, comparison.
Possibly if a member has one of the original 1,020 M-1866 Winchesters that we’re sent to Brazil in 1891, they can help out with you’re request in getting numbers with pictures, so you can find a machinist to help you duplicate a bolt that you are having a hard time finding.
A few M-1866 we’re and are converted from the .44 Henry Flat cartridge to the .44 Center Fire cartridge conversion you are seeking, using the original bolt, which IMO, would surly be a lot less challenging and work to accomplish!
Good Luck in you’re search.
Tony
March 25, 2024
Offline
ANTHONY thanks for your reply am wondering if Cody has any prints or drawings of a CF bolt that can be copied.Curious to know just how many 66 shooters are out there.My best to you and yours as always gene 66
May 2, 2009
Offline
I have been going through the Cody McCracken Library online and haven’t seen any drawing of the 66 or 73 bolts.
Bob
WACA Life Member--- NRA Life Member---- Cody Firearms member since 1991 Researching the Winchester 1873's
Email: [email protected]
March 21, 2011
Offline
This was discussed on here in June of 2023.
I found this discussion from ’17 on CAScity.com also.
March 25, 2024
Offline
1873man and darren thank you both for your help maybe it would be easier just to try and find a 66 rf bolt body only my best to you and yours gene66
March 25, 2024
Offline
ANTHONY lets see if we can locate a 66 bolt body stripped with nothing on it my best to you and yours gene66
March 31, 2009
Offline
Buy a 66 firing pin and the screw on piece that has the 2 strikers and modify these. The hard part is making the bushing that takes up the excess headspace. Winchester Bob sells the 2 parts but the bushing is on you.
Read the old posts.
March 25, 2024
Offline
CHUCK thanks for the help will check it out my best to you and yours gene 66
June 4, 2017
Offline
Winchester called the 1866 striker the snapper and the firing pin the piston. I have used Winchester Bob’s piston and thread on striker (snapper) and they worked. T/R
March 31, 2009
Offline
I used his parts to fix a Henry. There is a difference between the Henry and 66 piston length.
March 25, 2024
Offline
ANTONY if you get a chance go to44calwin1866 bolt look for AVALUER it shows two pictures of bolts in two places from 2013 one a cf and one just a clean bolt body just wanted to show you im still hunting my best as always to you and yours gene 66
December 9, 2002
Offline
gene66 said
ANTONY if you get a chance go to44calwin1866 bolt look for AVALUER it shows two pictures of bolts in two places from 2013 one a cf and one just a clean bolt body just wanted to show you im still hunting my best as always to you and yours gene 66
Gene,
That’s good work on finding that, as I know you’re search continues! Here’s the link.
Signed,
ANTNY
1 Guest(s)
