Avatar
Search
Forum Scope




Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_PrintTopic sp_TopicIcon
Buy a 38-55 and make yourself crazy
Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
1
November 17, 2026 - 4:55 am
sp_Permalink sp_Print sp_EditHistory

I recently bought a very handsome Winchester Model 1885 chambered in 38-55 Ballard/Winchester, one from the Limited Edition series made in 2004 by Miroku for Browning. I have no intention of buying a $90 box of current factory ammunition or shooting jacketed bullets. Instead. I bought a Redding three die set and an additional Redding competition seating die. A quantity of new Winchester brass and some new Starline brass, plus a box of Lightning 245 grain cast lead bullets sized to .378. 

I was forewarned about the modern SAAMI specification mismatch of a small chamber neck to a large groove diameter barrel, whereby a bullet sized big enough to seal the bore will, when seated in a case, result in a cartridge with a neck too fat to chamber in a rifle cut to SAAMI minimum chamber neck/mouth dimensions. 

THE ROOT OF THE PROBLEM:  Winchester sells factory 38-55 ammunition loaded with .3775 nominal diameter ( reportedly closer to .3665 ) thin jacketed PowerPoint bullets, which can swage down and be shot accurately in Miroku .375  bore diameter barrels with .376 ~ .377 grooves. 

And Miroku 38-55 chambers are cut to the SAAMI minimum diameter of .394, ignoring the SAAMI permitted manufacturing tolerance of +.002. At least mine is, as I empirically proved today.  A dummy cartridge I made up using the allegedly thinner neck walled Starline brass and seating the Lightning 245 grain .378 bullet to its crimping groove, was too fat in the neck to chamber. The neck miked .395. Let BT = brass thickness at the neck, PD = bullet diameter, and CND = cartridge neck diameter. If CND = 2(BT) + PD  and CND = .395 and PD = .378  then

(CND – PD)/2 = BT = .0085

When I say it wouldn’t chamber, I mean it stuck tight well before the base and head of the case could clear the forward edge of the rising bolt. The cartridge had to be pushed loose and out of the chamber by a cleaning rod inserted down the bore. 

My dial indicator actually reads the Starline brass thickness at the neck as .010, the same as my particular lot of Winchester brass. Despite Starline’s advertising its 38-55 brass is only .007 to .0075 at the neck, to help with the mismatch.  Maybe that is why Graf’s put these two bags of it on sale! 

If the brass had been, say .0075 instead of .0085, then the assembled cartridge would still have been .378 + .015 = .393,  which is iffy in a .394 chamber. SAAMI specs call for not less than .002 clearance. For comparison, most manufacturers of 30/06 ammunition size assembled cartridge necks for .006 clearance in SAAMI rifle chambers.  

Bert has suggested honing the chamber neck to increase diameter by .015, which would open it to .409.  The more I consider it, the better I like the idea.  I’ve emailed Ron and put the matter in front of him.  

I have the distinct impression Browning didn’t think people who bought these rifles in 38-55 would actually shoot them, or, they did, it would be with Winchester commercial ammunition. Well, one way or another, this one is going to shoot cast lead as JMB intended.  20261115_195037.jpg20261110_093828-1.jpgpix298433301.jpegpix242588614.jpeg

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
1892takedown
South Texas
Member
WACA Member
Forum Posts: 1183
Member Since:
March 20, 2010
sp_UserOfflineSmall Offline
2
November 17, 2026 - 6:58 am
sp_Permalink sp_Print

Before you resort to honing or any of that, try taking the decapping pin out of your sizing die and run the loaded cartridge (lubed) into the sizing die till you first feel resistance then give your lever a slight little bump (nothing drastic, ever so slight), this will compress the crimp/neck just enough to likely make a difference.  Then try chambering.  The slightest crimp used will still flare the brass at the neck = larger neck diameter however so slight. 

When I load for the 38-55, my case necks are 0.395 or thereabouts (sized cast bullet at .380 using Starline brass, brass trimmed to 2.105″, OACL 2.515″) when seated, by doing that extra slight step the neck diameter will be normally be reduced to 0.391 to 0.392 which will allow chambering.  0.392′ is the largest neck diameter that will chamber in the 1894 38-55, so Ive found.  May be worth a try and takes little effort.  

DSC_0245-Copy-3.JPG

1892takedown @sbcglobal.net ......NRA Endowment Life Member.....WACA Member

"God is great.....beer is good.....and people are crazy"... Billy Currington

Avatar
Dave M.
Member
WACA Member
Forum Posts: 64
Member Since:
December 25, 2022
sp_UserOfflineSmall Offline
3
November 17, 2026 - 11:22 am
sp_Permalink sp_Print

I agree with 1892takedown.

I do the same thing in order to chamber the Starline long brass, when loaded with a .381 LFPGC bullet. In my 1894 Commemorative with .379 groove dia.

It doesn’t take much, just a touch.

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
4
November 17, 2026 - 3:38 pm
sp_Permalink sp_Print sp_EditHistory

Good advice!  I’ll give it a try this morning and report back. 

If I can reduce the seated neck size to .392 from .395,  I expect it will chamber. That would save some bucks. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
1892takedown
South Texas
Member
WACA Member
Forum Posts: 1183
Member Since:
March 20, 2010
sp_UserOfflineSmall Offline
5
November 17, 2026 - 4:10 pm
sp_Permalink sp_Print

If you have a tubular magazine you have to crimp.  Just saying there seem to get a little flare in the brass at the crimp that will add a couple thousandths of an inch difference at the neck.  Even trying to adjust to the slightest crimp still seems to create a little flare in the brass.  

I have no experience loading for non-Winchester mfg., non-1894 guns.  Just gonna have to experiment a little. 

Chris

DSC_0245-Copy-3.JPG

1892takedown @sbcglobal.net ......NRA Endowment Life Member.....WACA Member

"God is great.....beer is good.....and people are crazy"... Billy Currington

Avatar
TXGunNut
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 7770
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
6
November 17, 2026 - 4:24 pm
sp_Permalink sp_Print

Zebulon said
Good advice!  I’ll give it a try this morning and report back. Chris, when you say “the slightest crimp used will still flare the brass at the neck, no matter how slight” — are you saying I should avoid crimping?
  

Maybe. The Single Shot rifle does not require a crimp but the components chosen may perform better with one. Several years ago I “discovered” the technique our S Texas friend described but have since learned it has been in use by astute reloaders of the 38-55 for some time. Since all my 38-55’s are 1894’s I apply a moderate roll crimp before kissing it with the sizing die. The sizing die applies what reminds me of the taper crimp I use on auto pistol cartridges. Matthew Wrobel wrote an excellent article for the Winter 2025 Collector on reloading for the 38-55, much of what he wrote applies to the modern Browning replica. 

 

Mike

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Board Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
7
November 17, 2026 - 5:07 pm
sp_Permalink sp_Print

I had wondered whether a taper crimp might do the trick. I dislike using uncrimped cartridges in the field, particulary in repeaters, even those with box magazines. In high intensity calibers, recoil–induced increased seating depth can cause trouble. 

I still like to perform the crimp separately from seating the bullet. If a bump with the seating die can reduce the seated neck .003,  that would get me shooting. 

I’ll take a look at the Collector article. 

Do you happen to know what sort of crimp Lee’s Factory Crimp die applies? I’ve never used one. I have used Lee’s Universal Expanding die satisfactorily, as a supplement to two-die sets. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
8
November 17, 2026 - 5:15 pm
sp_Permalink sp_Print

1892takedown said
If you have a tubular magazine you have to crimp.  Just saying there seem to get a little flare in the brass at the crimp that will add a couple thousandths of an inch difference at the neck.  Even trying to adjust to the slightest crimp still seems to create a little flare in the brass.  
I have no experience loading for non-Winchester mfg., non-1894 guns.  Just gonna have to experiment a little. 
Chris
  

Understood. Thanks, Chris. I’m fixing to go upstairs and give it a try.  Do you happen to recall the brass thickness at the neck of your 38-55 Starline cases?  They ballyhoo the alleged “.007 to .0075” of their case necks but the Starline short brass I got from Graf’s mikes the same as my Winchester brass — about .010. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
Bert H.
Kingston, WA
Admin
Forum Posts: 14974
Member Since:
April 15, 2005
sp_UserOfflineSmall Offline
9
November 17, 2026 - 5:17 pm
sp_Permalink sp_Print

It is not necessary (or desired in most cases) to crimp the bullet in place for a Single Shot rifle cartridge

For all many different Single Shot cartridges that I reload for, I simply resize (squeeze) the neck of the cartridges just enough to get a “snug” fit when seating the bullet.

Bert

WACA Historian & Board of Director Member #6571L
High-walls-1-002-C-reduced2.jpg

Avatar
1892takedown
South Texas
Member
WACA Member
Forum Posts: 1183
Member Since:
March 20, 2010
sp_UserOfflineSmall Offline
10
November 17, 2026 - 5:32 pm
sp_Permalink sp_Print sp_EditHistory

Zebulon said

1892takedown said
If you have a tubular magazine you have to crimp.  Just saying there seem to get a little flare in the brass at the crimp that will add a couple thousandths of an inch difference at the neck.  Even trying to adjust to the slightest crimp still seems to create a little flare in the brass.  
I have no experience loading for non-Winchester mfg., non-1894 guns.  Just gonna have to experiment a little. 
Chris
  

Understood. Thanks, Chris. I’m fixing to go upstairs and give it a try.  Do you happen to recall the brass thickness at the neck of your 38-55 Starline cases?  They ballyhoo the alleged “.007 to .0075” of their case necks but the Starline short brass I got from Graf’s mikes the same as my Winchester brass — about .010. 
  

With my Starline brass trimmed to 2.10-2.105″, Im still getting a thickness of .0075″, a few may go .008″. 

Bert and Mike better describe what I was trying to, slightly “squeezing” the neck to get a snug fit, or as Mike says, give it a little “kiss”Kiss

Also note, when doing this (getting a little too aggressive when giving it a kiss) your bullet may pull a little bit on the down-stroke and you may get a few thousandths of an inch longer overall cartridge.  

CH

DSC_0245-Copy-3.JPG

1892takedown @sbcglobal.net ......NRA Endowment Life Member.....WACA Member

"God is great.....beer is good.....and people are crazy"... Billy Currington

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
11
November 17, 2026 - 5:38 pm
sp_Permalink sp_Print

I think you are all saying the same thing: use the sizing die to squeeze the neck. The question I’m about to answer for myself is whether the apparently thicker brass I’ve got will size down from .395 to .392.  

Stay tuned…

 

  

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
TXGunNut
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 7770
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
12
November 17, 2026 - 5:51 pm
sp_Permalink sp_Print sp_EditHistory

Do you happen to know what sort of crimp Lee’s Factory Crimp die applies? I’ve never used one. I have used Lee’s Universal Expanding die satisfactorily, as a supplement to two-die set. -Zeb

 

I have no experience with the LFC dies, they apply the crimp in a different manner than conventional dies. I use the Lyman expander die and a variety of expanders. Lyman makes most common sizes and Buffalo Arms has or will make almost any other size you desire. When you can find them the RCBS Cowboy dies contain an expander die. I feel pretty sure your sizing die will reduce the neck to .392, the question is how the bullet will be affected.

It’s all speculation until the trigger is pulled.

 

Mike

 

Edited to correct diameter.

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Board Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
1892takedown
South Texas
Member
WACA Member
Forum Posts: 1183
Member Since:
March 20, 2010
sp_UserOfflineSmall Offline
13
November 17, 2026 - 6:05 pm
sp_Permalink sp_Print

TXGunNut said
Do you happen to know what sort of crimp Lee’s Factory Crimp die applies? I’ve never used one. I have used Lee’s Universal Expanding die satisfactorily, as a supplement to two-die set. -Zeb
 
I have no experience with the LFC dies, they apply the crimp in a different manner than conventional dies. I use the Lyman expander die and a variety of expanders. Lyman makes most common sizes and Buffalo Arms has or will make almost any other size you desire. When you can find them the RCBS Cowboy dies contain an expander die. I feel pretty sure your sizing die will reduce the neck to .392, the question is how the bullet will be affected.
It’s all speculation until the trigger is pulled.
 
Mike
  

I only have one Lee die set for the 45-60 so have no experience with Lee dies other than that.  Have been using the RCBS Cowboy dies for 15 or more years for the 38-55.  Agree with Mike in the above.  

DSC_0245-Copy-3.JPG

1892takedown @sbcglobal.net ......NRA Endowment Life Member.....WACA Member

"God is great.....beer is good.....and people are crazy"... Billy Currington

Avatar
TXGunNut
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 7770
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
14
November 17, 2026 - 6:16 pm
sp_Permalink sp_Print

One reason I like the RCBS Cowboy die set is they thoughtfully included .376 and .379 sizers for the expanding die. I don’t think they offer the Cowboy dies anymore but they may be worth looking for. I’m a big fan of Lee reloading equipment but haven’t had much luck with their loading dies. 

 

Mike

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Board Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
steve004
Member
WACA Member
Forum Posts: 5901
Member Since:
November 19, 2006
sp_UserOfflineSmall Offline
15
November 17, 2026 - 6:38 pm
sp_Permalink sp_Print

1892takedown said
Before you resort to honing or any of that, try taking the decapping pin out of your sizing die and run the loaded cartridge (lubed) into the sizing die till you first feel resistance then give your lever a slight little bump (nothing drastic, ever so slight), this will compress the crimp/neck just enough to likely make a difference.  Then try chambering.  The slightest crimp used will still flare the brass at the neck = larger neck diameter however so slight. 
When I load for the 38-55, my case necks are 0.395 or thereabouts (sized cast bullet at .380 using Starline brass, brass trimmed to 2.105″, OACL 2.515″) when seated, by doing that extra slight step the neck diameter will be normally be reduced to 0.391 to 0.392 which will allow chambering.  0.392′ is the largest neck diameter that will chamber in the 1894 38-55, so Ive found.  May be worth a try and takes little effort.  
  

I often do this.  Just a kiss.  Can make all the difference.

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
16
November 17, 2026 - 7:22 pm
sp_Permalink sp_Print sp_EditHistory

The short answer is the dummy cartridge now chambers. However, I can’t seem to get a good reading off my dial indicator on the resulting thickness. I will fetch my old Starrett T-230 and see what it reads. But I think the problem is solved. I will say it took a pretty good bump to get it squeezed down.

The dial indicator says its .393, once I got Dad’s old Luxo Magnifier plugged in. 

EDIT:  according to the Starrett T-230RL,  it is .3938.  I will have make up a couple more to be certain. The OACL on this dummy is 2.500. 

FURTHER EDIT:  I made up another dummy round, same bullet but using Winchester brass AND not crimping. Same OACL of 2.500.  This time, I had to haul down pretty hard on the Rockchucker’s handle to have any effect but the finished product looked smoother and chambered easily. The seated neck miked about the same, between .3935 and .394, so now I need to load some cartridges and see how it shoots. 

Because I have a lot of it, I think I’ll start off with 24 grains of RL7 and work up to 26 grains, stopping at best accuracy.  Lyman shows this load for their similarly shaped 249 grain #375248, listing a max load of 27.5 grains for 1768 fs. Their accuracy powder is similar 24- 25.8 of IMR 4198 but I don’t have any. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
Bert H.
Kingston, WA
Admin
Forum Posts: 14974
Member Since:
April 15, 2005
sp_UserOfflineSmall Offline
17
November 17, 2026 - 10:42 pm
sp_Permalink sp_Print

Bill,

I have used severeal different powders for my 38-55 (IMR 3031, IMR 4064), but long ago found that IMR 4198 is the best choice for consistency and accuracy.

Bert

WACA Historian & Board of Director Member #6571L
High-walls-1-002-C-reduced2.jpg

Avatar
steve004
Member
WACA Member
Forum Posts: 5901
Member Since:
November 19, 2006
sp_UserOfflineSmall Offline
18
November 17, 2026 - 11:17 pm
sp_Permalink sp_Print

Zebulon said
The short answer is the dummy cartridge now chambers. However, I can’t seem to get a good reading off my dial indicator on the resulting thickness. I will fetch my old Starrett T-230 and see what it reads. But I think the problem is solved. I will say it took a pretty good bump to get it squeezed down.
The dial indicator says its .393, once I got Dad’s old Luxo Magnifier plugged in. 
EDIT:  according to the Starrett T-230RL,  it is .3938.  I will have make up a couple more to be certain. The OACL on this dummy is 2.500. 
FURTHER EDIT:  I made up another dummy round, same bullet but using Winchester brass AND not crimping. Same OACL of 2.500.  This time, I had to haul down pretty hard on the Rockchucker’s handle to have any effect but the finished product looked smoother and chambered easily. The seated neck miked about the same, between .3935 and .394, so now I need to load some cartridges and see how it shoots. 
Because I have a lot of it, I think I’ll start off with 24 grains of RL7 and work up to 26 grains, stopping at best accuracy.  Lyman shows this load for their similarly shaped 249 grain #375248, listing a max load of 27.5 grains for 1768 fs. Their accuracy powder is similar 24- 25.8 of IMR 4198 but I don’t have any. 
  

Sometimes a light kiss does the trick, other times, a heavier kiss is needed.

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2526
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
19
November 17, 2026 - 11:45 pm
sp_Permalink sp_Print

Bert H. said
Bill,
I have used severeal different powders for my 38-55 (IMR 3031, IMR 4064), but long ago found that IMR 4198 is the best choice for consistency and accuracy.
Bert
  

I intend to buy some 4198 but have to order it, with the attendant hazmat fee that makes buying only a pound silly expensive. In the meanwhile, I’ve inherited a large quatity of of other powders and need to use some of those up. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Forum Timezone: UTC 0
Most Users Ever Online: 21294
Currently Online: Rick Hill, Burt Humphrey, 1873man, 28 gauge, tionesta1 (AL), deerhunter, Byron Russell, Henry Mero, TR, Gary Ryan, chief1966, Green River Gus, Pwog, Buck94, Larry21556, Honest Jon
Guest(s) 660
Currently Browsing this Page:
1 Guest(s)
Top Posters:
TXGunNut: 7769
clarence: 7119
Chuck: 6924
steve004: 5901
1873man: 5009
deerhunter: 3079
twobit: 2765
Big Larry: 2578
mrcvs: 2552
Zebulon: 2526
Newest Members:
Banjo
Gary Reighard
Dirtcurt
HEISAP
Jetskibratttt
Dermot
wacopiper7
Sboatright
Thomas S
Forum Stats:
Groups: 1
Forums: 18
Topics: 16479
Posts: 151035

 

Member Stats:
Guest Posters: 2057
Members: 11090
Moderators: 3
Admins: 4
Administrators: Mike Hager, Bert H., JWA, SethJ
Moderators: Rob Kassab, Brad Dunbar, Heather
Navigation