Avatar
Search
Forum Scope




Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_PrintTopic sp_TopicIcon
Early Model 63
Avatar
drice0517
Member
WACA Member
Forum Posts: 20
Member Since:
January 15, 2025
sp_UserOfflineSmall Offline
1
November 15, 2026 - 2:14 pm
sp_Permalink sp_Print

Came across this old 63 in a local sale recently and I’m in the process of fixing it up a little. Made in ’38 or ’39 by the serial number, depending on the source, but the barrel is stamped “38” underneath the front stock just in front of the receiver. It’s been well used but it loads, shoots, and ejects nicely. The bore is good and will probably get better after some shooting and a good cleaning. The shells jump strongly into the chamber when the operating rod is cycled and the bolt recoil is strong. I shot both CCI SV and Federal AutoMatch and it handled both without a hitch. The firing pin is making nice indents on the shell rim. I didn’t pay much attention to targeting but it grouped pretty good, hitting high and left a few inches at 30 yards. I’ll make some sight adjustments later.

My initial plan is too take it apart, clean/inspect the parts, and get rid of the shiny finish somebody put on it. I’m not sure what they used but it’s on there pretty good, it’s not soft or sticky. I’ve repaired some wood cracks before, but I’d like some opinions on whether to replace the stock and butt plate or repair these. The stock was a little loose on the tang but I tightened the stock nut and fixed that. The concern I have with the cracked stock is that the stock doesn’t fit well to the tang and receiver and the glued nails won’t let me close the cracks any further using a clamp to make a better fit. I think if I could remove the nails I might be able to re-glue it, clamp it tight, maybe using wooden dowels to make it a stronger repair. Suggestions..?

I’m just wanting a decent looking shooter grade 63 and will probably just clean the metal up and use some cold blue. The butt plate (and fore cap) have some pitting that I’ll try to clean up with files and some polishing if it’s no too deep. If the stock can be repaired I’d like to try remove the nails and repair it before i look into buying a good used one, and maybe find and buy a smooth butt plate too. I’m looking for suggestions, opinions, and directions as to how to repair the cracks and what may be the better methods for refinishing the metal and wood. The metal looks better in the photos than it does up close (except for the butt plate). I’ve done some cold bluing in the past but it’s been awhile and I know there may be some newer cold blue products and methods that might be better than what I’ve done in the past. Thanks for the help, and in case I need them, if anybody has a source for the stock and smooth butt plate I would appreciate the information.

77AC2E42-65EB-4F27-B20E-FFF85BBAE636_1_105_c.jpeg 

 

FA043638-4F0C-4EF8-9D64-37AD97309CAE_1_105_c.jpeg19D2769A-F9C2-4D28-B1AA-524C05E74340_1_105_c.jpegC8BD75CD-DC56-4D5B-AD63-DF686BA8584E_1_105_c.jpegg

Avatar
TXGunNut
Northern edge of the D/FW Metromess
Member
WACA Member
Forum Posts: 7757
Member Since:
November 7, 2015
sp_UserOfflineSmall Offline
2
November 15, 2026 - 2:52 pm
sp_Permalink sp_Print

Homestead lists original and reproduction stocks and original butt plates but currently out of stock on all. If you ask they will contact you when they get them in. In the meantime the wood repairs may be a nice winter project, sounds like you have some experience in that area. If the receiver doesn’t move in the stock it may be less risky to reinforce and fill the cracks with dyed bedding compound and enjoy shooting a fun little rifle.  My 63 has two holes neatly drilled in the left side of the receiver but they don’t bother me a bit. It was pictured in the Collector article about T. C. Johnson and the Model 1903 awhile back and Brad thoughtfully used the photo of the right side of the receiver. 

 

Mike

Life Member TSRA, Endowment Member NRA
BBHC Member, TGCA Board Member
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.-TXGunNut
Presbyopia be damned, I'm going to shoot this thing! -TXGunNut
Avatar
EWMN
Member
WACA Member
Forum Posts: 75
Member Since:
October 14, 2025
sp_UserOfflineSmall Offline
3
November 15, 2026 - 3:18 pm
sp_Permalink sp_Print

drice0517 said
Came across this old 63 in a local sale recently and I’m in the process of fixing it up a little. Made in ’38 or ’39 by the serial number, depending on the source, but the barrel is stamped “38” underneath the front stock just in front of the receiver. It’s been well used but it loads, shoots, and ejects nicely. The bore is good and will probably get better after some shooting and a good cleaning. The shells jump strongly into the chamber when the operating rod is cycled and the bolt recoil is strong. I shot both CCI SV and Federal AutoMatch and it handled both without a hitch. The firing pin is making nice indents on the shell rim. I didn’t pay much attention to targeting but it grouped pretty good, hitting high and left a few inches at 30 yards. I’ll make some sight adjustments later.
My initial plan is too take it apart, clean/inspect the parts, and get rid of the shiny finish somebody put on it. I’m not sure what they used but it’s on there pretty good, it’s not soft or sticky. I’ve repaired some wood cracks before, but I’d like some opinions on whether to replace the stock and butt plate or repair these. The stock was a little loose on the tang but I tightened the stock nut and fixed that. The concern I have with the cracked stock is that the stock doesn’t fit well to the tang and receiver and the glued nails won’t let me close the cracks any further using a clamp to make a better fit. I think if I could remove the nails I might be able to re-glue it, clamp it tight, maybe using wooden dowels to make it a stronger repair. Suggestions..?
I’m just wanting a decent looking shooter grade 63 and will probably just clean the metal up and use some cold blue. The butt plate (and fore cap) have some pitting that I’ll try to clean up with files and some polishing if it’s no too deep. If the stock can be repaired I’d like to try remove the nails and repair it before i look into buying a good used one, and maybe find and buy a smooth butt plate too. I’m looking for suggestions, opinions, and directions as to how to repair the cracks and what may be the better methods for refinishing the metal and wood. The metal looks better in the photos than it does up close (except for the butt plate). I’ve done some cold bluing in the past but it’s been awhile and I know there may be some newer cold blue products and methods that might be better than what I’ve done in the past. Thanks for the help, and in case I need them, if anybody has a source for the stock and smooth butt plate I would appreciate the information.
 
 
g
  

Nice rifle, I definitely have a soft spot for the 63s. My pal-pal had one from the 50s. He had a 320 acre farm in south Missouri, wasn’t a working farm but a mostly woodd retreat for hunting and lord knows I shot a few squirrels with that 63, it was scoped. Pal – pal always made squirrel with biscuits and gravy, amazing breakfast. I’m always looking for a good 63, it won’t be pal-pals but thats ok.

Avatar
Henry Mero
Member
WACA Member
Forum Posts: 1647
Member Since:
December 21, 2006
sp_UserOfflineSmall Offline
4
November 15, 2026 - 3:22 pm
sp_Permalink sp_Print

Without holding that stock in hand, I do believe it is “fixable” with a little warmed up Gorilla glue , a turkey baster syringe and a furniture clamp.

W.A.C.A. life member, Marlin Collectors Assn. charter and life member, C,S.S.A. member and general gun nut.

Avatar
Zebulon
Texas
Member
WACA Member
Forum Posts: 2514
Member Since:
January 20, 2023
sp_UserOfflineSmall Offline
5
November 15, 2026 - 3:58 pm
sp_Permalink sp_Print sp_EditHistory

I’d definitely stay with the original stock, which I think is very fixable. 

I haven’t seen a dorsal view of the inletting but I would go a little further than Hank and use Acraglass. 

I would take a narrow V-chisel and enlarge the tops of the interior crack line and across the face of the stock wrist. I would also cross-hatch the face to give bedding compound more purchase. 

Then, after applying release agent whereever there will be overruns, I would get as much Acraglass Gel bedding compound (peanut butter consistency) into the cracks and across the face of the wrist as possible, then reassemble the stock to the receiver and clamp the wrist with elastic bands and perhaps a wood clamp.

I should have mentioned, fill the tang screw holes with modeling clay first, to keep Acraglass out of the threads. Leave out the screws until the glass is cured.

I’d leave the nail heads in place but you could drill them out and fill the cavities with larger steel.pins coated in Acraglass. You could make them flush with the stock surface or make them short enough to conceal.with ebony or matching walnut plugs. 

As for refinishing the stock. All that is needed, if the topcoat has not failed, is to touch up the pin holes or plugs, then go over the whole stock lightly with 0000 wool to knock back the gloss to satin. 

The advantage to Acraglass is it is more gap filling and provides structural strength.

When possible, I prefer a repaired original stock to a new semi-inletted stock. It is a.hell of a lot less work. And it preserves the originality of the gun. There are limits, of course. 

- Bill 

 

WACA # 65205; life member, NRA; member, TGCA; member, TSRA; amateur preservationist

"I have seen wicked men and fools, a great many of both, and I believe they both get paid in the end, but the fools first." -- David Balfour, narrator and protagonist of the novel, Kidnapped, by Robert Louis Stevenson.

Avatar
Jim F in CT
Member
WACA Guest
Forum Posts: 102
Member Since:
December 13, 2006
sp_UserOfflineSmall Offline
6
November 15, 2026 - 4:18 pm
sp_Permalink sp_Print sp_EditHistory

 My 63 has two holes neatly drilled in the left side of the receiver but they don’t bother me a bit. . . . . .
  

My 63 has two holes also . . .I guess for a side-mount scope base.

My only complaint about the 63 is, ”it’s a BEAR to clean THOROUGHLY”!

Avatar
Chuck
Member
WACA Member
Forum Posts: 6922
Member Since:
March 31, 2009
sp_UserOfflineSmall Offline
7
November 15, 2026 - 9:28 pm
sp_Permalink sp_Print

Have you tried to squeeze the stock with a clamp?  You may be able to loosen the grasp on the nails.  If so, put some wood glue in the cracks and then clamp.  If the nails stick out, you can try to pull on them or just sand off the ends. 

Avatar
drice0517
Member
WACA Member
Forum Posts: 20
Member Since:
January 15, 2025
sp_UserOfflineSmall Offline
8
November 16, 2026 - 1:35 am
sp_Permalink sp_Print

Thanks for the replies and suggestions…yes, I’ve tried to close the crack with just clamp pressure…seems that some type of glue was used with the nails and whatever it is it’s stout..! I can’t drive the nails in to close the cracks and can’t use a clamp to close it. I would up cutting the top nail out through the crack and opening it up a little to get some wood glue in then clamped it. The crack closed up pretty good but I’m not sure the wood glue will hold the tension when I remove the clamp. I would have liked to just fill the cracks and leave it as is but the stock wasn’t fitted to the tang metal very well and stuck out just a little too much on one side. If the stock fit the tang better I might have tried the Acraglass mentioned above. I’ve never used it and this might have been a good chance to try it out. I ordered some walnut dowels today and if it won’t hold with wood glue I’ll drill the nails out and glue in some pieces of walnut dowels using good glue and a clamp. I didn’t know they made the walnut dowels…they come in assorted packaging and sizing (sizes I ordered are about 1/16 to 1/4 inch, about 6 inches long). If anybody might have need of some down the road give me a holler and I’ll mail you some. I think the rest of the fixing up will be pretty straight forward if I can get this original stock to stay together and fit good. And no telling how the cold blue will turn out..seems like it turns out a little different each time I try it…maybe the metal that’s getting blued or maybe it’s operator error, I don’t know..Smile

Fun work though, I enjoy it..! Appreciate everyone’s time..!

Avatar
Jeremy P
The Great State
Member
WACA Member
Forum Posts: 1446
Member Since:
April 30, 2023
sp_UserOfflineSmall Offline
9
November 16, 2026 - 4:01 am
sp_Permalink sp_Print

Not sure Homestead is up and running right now…got an older order pending and no contact from them despite a few attempts. I will create a new thread to ask about it…

Forum Timezone: UTC 0
Most Users Ever Online: 21294
Currently Online: jolly bill, DEEREHART, 86Win
Guest(s) 1281
Currently Browsing this Page:
1 Guest(s)
Top Posters:
TXGunNut: 7757
clarence: 7119
Chuck: 6922
steve004: 5899
1873man: 5008
deerhunter: 3079
twobit: 2765
Big Larry: 2578
mrcvs: 2552
Zebulon: 2514
Newest Members:
HEISAP
Northman
Jetskibratttt
Dermot
wacopiper7
Sboatright
Thomas S
Marcus Horne
kirtmorris
Coachgun
Forum Stats:
Groups: 1
Forums: 18
Topics: 16469
Posts: 150959

 

Member Stats:
Guest Posters: 2057
Members: 11088
Moderators: 3
Admins: 4
Administrators: Mike Hager, Bert H., JWA, SethJ
Moderators: Rob Kassab, Brad Dunbar, Heather
Navigation