Avatar
Search
Forum Scope




Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_PrintTopic sp_TopicIcon
Model 1910 Drill and Tapped Receiver help!
Avatar
Steven Gabrielli
LI NY
Member
WACA Member
Forum Posts: 348
Member Since:
August 14, 2021
sp_UserOfflineSmall Offline
1
December 27, 2023 - 12:22 am
sp_Permalink sp_Print

So I removed the screws from the upper receiver that were drilled and tapped back in the day, and I saw the rear 2 holes go straight through, the most forward hole does not. I honestly don’t know if this is ok? Is the enough pressure left once the bolt heads rearward to be dangerous?

Thx 

SteveIMG_0580.jpegImage Enlarger

sp_PlupAttachments Attachments
Avatar
clarence
NY
Member
Restricted
Forum Posts: 7119
Member Since:
November 1, 2013
sp_UserOfflineSmall Offline
2
December 27, 2023 - 12:47 am
sp_Permalink sp_Print

Steven Gabrielli said Is the enough pressure left once the bolt heads rearward to be dangerous?

Not a cause for concern.  Getting the ammo for it–that’s a concern.

Avatar
Steven Gabrielli
LI NY
Member
WACA Member
Forum Posts: 348
Member Since:
August 14, 2021
sp_UserOfflineSmall Offline
3
December 27, 2023 - 12:58 am
sp_Permalink sp_Print

Thank you my friend, I was getting ready to take a blood pressure pill. Ammo is in process. Finding a mount is another story. Any ideas on that?

 

SteveIMG_0581.jpegImage Enlarger

sp_PlupAttachments Attachments
Avatar
clarence
NY
Member
Restricted
Forum Posts: 7119
Member Since:
November 1, 2013
sp_UserOfflineSmall Offline
4
December 27, 2023 - 1:34 am
sp_Permalink sp_Print

 Finding a mount is another story. Any ideas on that?Steven Gabrielli said

  

“Pill” did you say?  My daily dose is a handful.  Finding a mount is much less concerning:  just buy one of the many “rails” that accept Weaver rings, such as those made by EGW.  They might make one the exact length you need, but if not, buy one a little longer & cut it off with a hacksaw; then drill the holes you need.  I’ve done it, proving it CAN’T be hard!

Forum Timezone: UTC 0
Most Users Ever Online: 4623
Currently Online: Chuck, mrcvs, Tedk, DEEREHART, TXGunNut, jsgwoodsman, freebird1968, [email protected], Bill Yadlosky, gene66, Wiresguy
Guest(s) 56
Currently Browsing this Page:
1 Guest(s)
Top Posters:
clarence: 7119
TXGunNut: 6458
Chuck: 5867
steve004: 5209
1873man: 4703
deerhunter: 2711
Big Larry: 2559
twobit: 2505
mrcvs: 2212
Maverick: 2042
Newest Members:
Ricky Summer
Peter Cipollini
Jhark
Oldtimer52
parkerposy
rayhobbs
WebleyScott
Task1
1886
Forum Stats:
Groups: 1
Forums: 18
Topics: 14809
Posts: 132538

 

Member Stats:
Guest Posters: 2057
Members: 10045
Moderators: 3
Admins: 4
Administrators: Mike Hager, Bert H., JWA, SethJ
Moderators: Rob Kassab, Brad Dunbar, Heather
Navigation