Log In
August 2, 2006
Offline
Hello all, not new to forum but been away a number of years. Inherited some rifles years ago from Dad, keeping several, but going to let go of a few. Computer not letting me upload photos, error msg telling me ” source is unavailable, or destination is full or read only”. Any IT minds have suggestions they are welcome. Can send pics from phone. P.M. if interested.
model 1901 – rolling block shotgun 10 ga. very good condition s/n 702xx $1200
1866 – SRC .44-40 poor condition no firing pin (attempted conversion) s/n 103xxx $1150
1873 – 24″ octagonal barrel overall poor condition 32-20 s/n 449xxxB $1500
1895 – flatside good condition 30-40 Krag buckhorn sight – top of right horn broken – s/n 14xx $1600
’64 – very good condition .219 zipper (awesome shooter) s/n 112xxx $1400
’55 – .30 WCF very good condition s/n 108xxxx $900
Also: Ruger Super Blackhawk 44 mag 7″ barrel stainless black grips exc. condition less than 100 rounds. $500
I’m no expert, many here on site. Advice appreciated. Good day to all.
Thx Dan
April 15, 2005
Offline
Please edit your post and put the complete serial numbers in your list.
Bert
WACA Historian & Board of Director Member #6571L
July 17, 2012
Offline
danjen said
Hello all, not new to forum but been away a number of years. Inherited some rifles years ago from Dad, keeping several, but going to let go of a few. Computer not letting me upload photos, error msg telling me ” source is unavailable, or destination is full or read only”. Any IT minds have suggestions they are welcome. Can send pics from phone. P.M. if interested.
1866 – SRC .44-40 poor condition no firing pin (attempted conversion) s/n 103xxx $1150
Also: Ruger Super Blackhawk 44 mag 7″ barrel stainless black grips exc. condition less than 100 rounds. $500
Thx Dan
Dan,
I sent you a PM regarding the 1866 and the Ruger .44
Thanks,
WACA Life Member #6284 - Specializing in Pre-64 Winchester .22 Rimfire
August 2, 2006
Offline
Good morning, a little help please
Bert – how to edit
JWA – are PMs directed to email? If si did not receive
February 28, 2008
Offline
Where are you located?
If you’re not too far away from me, I might want to come look at these.
January 11, 2011
Offline
PM sent 30 min ago on the model 66. Please text pics to the phone number included.
Thanks,
LSH.
November 7, 2015
Offline
I’m not Bert but if you’ll find the “Edit” box in the upper right corner of your original post and click it you will be taken to the edit page. After making your changes click the “save changes” box below your post.
Mike
April 20, 2011
Offline
hi, ia am interested in a couple of your guns. you can call me at 207-522-0939 or email [email protected] thanks, dana
August 2, 2006
Offline
Well, I’ve been looking for that edit tab. I see delete – quote – report tabs only. I’ve had two cups of coffee, what am I missing?
May 2, 2009
Offline
If someone sends you a PM you will get a email notice if you have it set up that way or there is a MAIL button near the top that will take you to the Private Mail system. My guess as a Guest you can’t edit your posts and send or receive PM’s if you are not seeing the buttons. You can always add a reply with the information again instead of editing.
Bob
WACA Life Member--- NRA Life Member---- Cody Firearms member since 1991 Researching the Winchester 1873's
Email: [email protected]
July 17, 2012
Offline
Did you find my pm from last night regarding the 1866 and Ruger? A pm is not an email, they are separate. Your email address was not listed in your profile. I would like both the 1866 and Ruger and sent you my email address: [email protected]
Check your inbox at the top of the screen for pm’s.
Regards,
WACA Life Member #6284 - Specializing in Pre-64 Winchester .22 Rimfire
November 27, 2013
Offline
Danjen, I also sent you a PM yesterday, but haven’t heard back. I’m interested in a couple of them. I can be reached at:
Mark Douglas
August 2, 2006
Offline
Got PMs today. Thank you for interest. Jammin this am, will respond in afternoon. Dan.
August 2, 2006
Offline
I responded to all PMs with a msg saying will work the list when morning freed up. It did, but when I go to PMs all I see on each PM is the last msg I sent. Is it possible to view PMs as a thread?
April 15, 2005
Offline
In answer to your question, No it is not… you need to click on each message in the PM topic to read them individually. You can open them all, and scroll through them.
Bert
WACA Historian & Board of Director Member #6571L
August 2, 2006
Offline
Thank you Bert. I must be doing something incorrectly. When I click on a specific PM, I get last msg sent only. How can I see previous comments on same PM? Please advise.
April 15, 2005
Offline
danjen said
Thank you Bert. I must be doing something incorrectly. When I click on a specific PM, I get last msg sent only. How can I see previous comments on same PM? Please advise.
I frankly have no idea what you might be doing wrong. I have tried to explain to you how to use the PM system, but without the ability to see what you are doing, I am at a loss as to how to assist you further.
Bert
WACA Historian & Board of Director Member #6571L
1 Guest(s)
