Avatar
Search
Forum Scope




Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_PrintTopic sp_TopicIcon
1886 Hammer
Avatar
Remmag
NE Ohio
Member
WACA Guest
Forum Posts: 12
Member Since:
August 6, 2018
sp_UserOfflineSmall Offline
1
August 6, 2018 - 1:42 am
sp_Permalink sp_Print

Hi folks, new member – first post. I have a question about the hammer – bolt relation on a 1886. When the bolt is fully to the rear should there clearance between the top of the hammer and the bottom of the bolt?

Avatar
1873man
Wisconsin
Member
WACA Member
Forum Posts: 4723
Member Since:
May 2, 2009
sp_UserOfflineSmall Offline
2
August 6, 2018 - 2:16 pm
sp_Permalink sp_Print

I just checked mine and there is not be any clearance between them since the bolt is what pushes the hammer to the cock position. When you work the action does the hammer go to full cock?

Bob

WACA Life Member---
NRA Life Member----
Cody Firearms member since 1991
Researching the Winchester 1873's

73_86cutaway.jpg

Email: [email protected]

Avatar
Remmag
NE Ohio
Member
WACA Guest
Forum Posts: 12
Member Since:
August 6, 2018
sp_UserOfflineSmall Offline
3
August 6, 2018 - 2:51 pm
sp_Permalink sp_Print

Yes, it cocks but as the bolt travels past the hammer it pushes very hard against the bottom of the bolt, making the action very hard to cycle. I think the main spring is to strong or the bolt is a little to tall. Very hard to cycle.

Avatar
1873man
Wisconsin
Member
WACA Member
Forum Posts: 4723
Member Since:
May 2, 2009
sp_UserOfflineSmall Offline
4
August 6, 2018 - 3:27 pm
sp_Permalink sp_Print

Put a little grease on the bottom of the bolt and see if that helps. I believe there is a spring tension adjuster just like the 73’s have, check that to see if its been turned in.

Bob

WACA Life Member---
NRA Life Member----
Cody Firearms member since 1991
Researching the Winchester 1873's

73_86cutaway.jpg

Email: [email protected]

Avatar
Remmag
NE Ohio
Member
WACA Guest
Forum Posts: 12
Member Since:
August 6, 2018
sp_UserOfflineSmall Offline
5
August 6, 2018 - 4:37 pm
sp_Permalink sp_Print

Thanks for the reply Bob. Lack of lube is not the problem. I’ll check for the tensioner when I get a chance. 

Forum Timezone: UTC 0
Most Users Ever Online: 5406
Currently Online:
Guest(s) 828
Currently Browsing this Page:
1 Guest(s)
Top Posters:
clarence: 7119
TXGunNut: 6584
Chuck: 5947
steve004: 5239
1873man: 4723
deerhunter: 2717
Big Larry: 2567
twobit: 2519
mrcvs: 2217
Maverick: 2044
Newest Members:
Johnny Fresh
Ebrown
Jamo
WesternTradingPost
mr.rudolph
Roscoe
EWMN
Winchesterwows
jacksontod71
KPotter44
Forum Stats:
Groups: 1
Forums: 18
Topics: 14901
Posts: 133607

 

Member Stats:
Guest Posters: 2057
Members: 10124
Moderators: 3
Admins: 4
Administrators: Mike Hager, Bert H., JWA, SethJ
Moderators: Rob Kassab, Brad Dunbar, Heather
Navigation