TXGunNut said
May want to try another lot of primers. Any word from Lee?
 
Mike
  

Mike, this is the same lot I have been shooting for the other express cartridges too.  When I de capped the primer the guts had fallen out somewhere. 

No word from Lee Precision.  I've been thinking about this a lot lately.  They won't let you talk with the shop personnel.  I need to find a way to get passed the lady that answers the phone calls and relays all the messages.

Chuck said
I fired, or tried to fire, the 3 cartridges yesterday.  The first one graphed at 1,221 fps.  Low but it was a cold bore shot.  I was expecting the next 2 to speed up some.  The second one did not fire.  Bad primer.  It shows a good firing pin hit.  The third one really surprised me.  The chronograph showed only 981 fps?
I guess I need to shoot some more and increase the powder by another grain to 31.  
  

Chuck,

IMR 4198 is not conducive to excessively light loads.  Load it at +1 grain above the recommended minimum charge weight, and then work up from there.

Bert

Mike

I guess I need to shoot some more and increase the powder by another grain to 31.  

slk said
I found this link to be good info for the bullet that speer makes for the 218 bee especially for the lever action with tubular magazine. 
 
https://reloadingdata.speer.com/downloads/speer/reloading-pdfs/rifle/218_Bee_46.pdf
  

I recently picked up an un-fired Browning 65 and I laid in a nice supply of these Speer bullets.

I also have a handful of the best powders for the Bee in my stash.  Looking forward to playing with it when I finish building the house and can get the loading room set up again!

Zebulon said
With all that Hornet brass stocked up in your reloading room, I don't see how you have room to pull the press handle. 
  

Currently, I still have 14,000+ Hornet cases (loaded and empties), with 2,500 spoken for that I will deliver at the Cody show.  While that may seem like a lot, I have room for at least 5X that in my reloading room.  Being an old (retired) Submariner, I am an expert at organizing, packing, and storing a lot of stuff into limited spaces.

Bert

Zebulon said

Bert H. said

slk said
I was able to pick up the lyman cast bullet book today. Not a lot of options for cast in 218 but i like it for a lot of the other calibers i cast for. 
Actually I guess you can expect there to be lots of loads for it. 
I use that same bullet mold 225438 for my 22 hornet loads. For some reason I have never been able to get good groups from a cast bullet in 22 hornet. I have a Rugger in 22 hornet that i can drive nails in with if i use the hornady varment bee jacketed bullet. The cast bullets to date have been quite disappointing for the hornet. 
  

This is just my opinion, but varmint cartridges (like the 218 Bee and 22 hornet) were never designed to shoot low velocity or cast bullets.  From many years of experience, the 22 Hornet excels when the velocities are near the maximum end of the scale... not something you can do when shooting cast bullets.  If you cannot shoot sub MOA groups with your 22 Hornet, change your load specs to something with a faster velocity.
Bert
  

Bert,  I agree with you neither cartridge was designed for cast lead and, if accuracy is the criterion, a 45 grain spitzer [or a 35 grain V-max] at near maximum velocities is the clear answer. My [former] Anschutz Hornet was the most accurate rifle I've ever owned. The krauts voided any warranty if you shot handloads - probably afraid of stretched case separations from the low-shouldered case AND their rear-locking Match 64 action. But it was a tackdriver. 
Now, the Anschutz barrel was rifled with a 1-14 twist, which seems to have been the convention for the cartridge.  However, the Hornet for which I once loaded some 50-52 grain cast lead at <2000 fs,  was a Kimber of Oregon 82B with a 1-10 barrel. While the load was never meant for more than minute of gobbler or hen ( in the Fall), it  was capable of near one MOA at 75 yards. 
We can doubtless agree the better edible small game load is a 25 or 32 WCF -- or a Krag shooting 110 grain .308 bullets over 4759 -- but perhaps the inaccuracy people experience with cast lead in the Hornet is at least partially due to low velocity plus slow rate of twist. 
  

I spent 2+ hours in my reloading (man) cave last evening loading up a sizeable batch of 22 Hornets using a 40-gr V-Max.  I chose 12.5 grains of Lil Gun and loaded it in a full box (50) Remington (R - P) nickel plated brass cases.  I intend to shoot them in the Model 54 Hornet I bought from Ted and Lou kindly delivered to me at the Cody show last year.  Just for fun, I loaded a smaller batch with 13.0 grains (a slightly compressed load).  Those 40-grain V-Max bullets are real pretty!

For those that might be in need of 22 Hornet brass, I still have 5,000 W-W SUPER NPEs, and 2,600 R-P Match NPEs that are for sale.  I will bring it all with me to the Cody show this year for those who want to pick it up in person.

Bert

tim tomlinson said
I have an old farmer friend who casts a lot of lead bullets.  Years ago he was one who Lyman would call and ask for help.  Anyway, he spent the winter casting .22 gas check bullets and testing in two identical .223 rifles.  One would shoot nice 50 yard groups while the other looked like he was shooting buck shot.  Unlike me, he has steady hands and still had gas checks all over the floor and had a very hard time getting them on straight on the bullet shanks.  My 86 grain bullet for the .25-20 is now beyond my ability to do.  Drop bullets, drop or shake powder out of the case, etc.  My left hand is the worse of the two and I have long ingrained habit of handling cartridges and bullets with the left to put onto the cartridge holder of my press.  I can't even imagine handling tiny cast gas checks or cast bullets in .22 calibers.  The very base of a bullet is critical to be straight, fully filled and square.  Magnification for inspection is necessary to having good and consistent bullets.  Its easier the bigger the bullet! You are in an area many  fear to go.  Tim
  

Tim,  although the ravages of age frustrate us all, the solution for tremor -- which comes and goes for me, too -- and small bore, gas checked bullets, is a phone call or Web order to one of the fine commercial bullet casters.  A virtual swipe of your plastic and like magic a box of very nice .224 gas-checked, cast lead bullets will appear at your door. Brought to you by a sweating, cursing mail person. Trust me. 

Bert H. said

slk said
I was able to pick up the lyman cast bullet book today. Not a lot of options for cast in 218 but i like it for a lot of the other calibers i cast for. 
Actually I guess you can expect there to be lots of loads for it. 
I use that same bullet mold 225438 for my 22 hornet loads. For some reason I have never been able to get good groups from a cast bullet in 22 hornet. I have a Rugger in 22 hornet that i can drive nails in with if i use the hornady varment bee jacketed bullet. The cast bullets to date have been quite disappointing for the hornet. 
  

This is just my opinion, but varmint cartridges (like the 218 Bee and 22 hornet) were never designed to shoot low velocity or cast bullets.  From many years of experience, the 22 Hornet excels when the velocities are near the maximum end of the scale... not something you can do when shooting cast bullets.  If you cannot shoot sub MOA groups with your 22 Hornet, change your load specs to something with a faster velocity.
Bert
  

Bert,  I agree with you neither cartridge was designed for cast lead and, if accuracy is the criterion, a 45 grain spitzer [or a 35 grain V-max] at near maximum velocities is the clear answer. My [former] Anschutz Hornet was the most accurate rifle I've ever owned. The krauts voided any warranty if you shot handloads - probably afraid of stretched case separations from the low-shouldered case AND their rear-locking Match 64 action. But it was a tackdriver. 

Now, the Anschutz barrel was rifled with a 1-14 twist, which seems to have been the convention for the cartridge.  However, the Hornet for which I once loaded some 50-52 grain cast lead at <2000 fs,  was a Kimber of Oregon 82B with a 1-10 barrel. While the load was never meant for more than minute of gobbler or hen ( in the Fall), it  was capable of near one MOA at 75 yards. 

We can doubtless agree the better edible small game load is a 25 or 32 WCF -- or a Krag shooting 110 grain .308 bullets over 4759 -- but perhaps the inaccuracy people experience with cast lead in the Hornet is at least partially due to low velocity plus slow rate of twist. 

Seating the bullet on top of the brass is where I drop some. It is a balancing act to get them started straight. 

I have 3 loads ready to go for the 218 bee. One is a cast bullet. One is the speer flat nose. One is the hornady varment bee. All are .224  in 46 grain. Just have to get to the range and see which one does the best. 

slk said
I was able to pick up the lyman cast bullet book today. Not a lot of options for cast in 218 but i like it for a lot of the other calibers i cast for. 
Actually I guess you can expect there to be lots of loads for it. 
I use that same bullet mold 225438 for my 22 hornet loads. For some reason I have never been able to get good groups from a cast bullet in 22 hornet. I have a Rugger in 22 hornet that i can drive nails in with if i use the hornady varment bee jacketed bullet. The cast bullets to date have been quite disappointing for the hornet. 
  

This is just my opinion, but varmint cartridges (like the 218 Bee and 22 hornet) were never designed to shoot low velocity or cast bullets.  From many years of experience, the 22 Hornet excels when the velocities are near the maximum end of the scale... not something you can do when shooting cast bullets.  If you cannot shoot sub MOA groups with your 22 Hornet, change your load specs to something with a faster velocity.

Bert

Mike